S H D - 3 0 6 1 A SAMSUNG NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1478| 977| | Capacity form/unform 59/ MB Heads 2| 7| | Seek time / track 15.0/ 5.0 ms Sector/track | 17| | Controller IDE / AT Precompensation 65535 Cache/Buffer 32 KB LOOK-AHEAD Landing Zone Data transfer rate 1.563 MB/S int Bytes/Sector 512 6.000 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g 5 | 75 seek W Rotation RPM read/write W Acoustic dBA spin-up W ECC Bit MTBF h 200000 Warranty Month 12 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** SAMSUNG SHD-3101A/3062A/3061A USER'S MANUAL 264-014033BAAC +---------------------------------------------------------+xx1 J6 | +-+-+-+-+-+-+-+-+ J3 |XX Power | ECC--+-+-+-+-+-+-+-+-+ | | | | |XX J1 | DSP-+ -C/D |XX AT-Bus | |XX | |XX | |XX | |XX | |XX | |XX | |XX | |XX | |XX | | 1 | |XX Power | |XX J5 +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** SAMSUNG SHD-3101/3062/3061-A HARD DISK DRIVE USER'S MANUAL 264-01403 Jumper Setting ============== x = Jumper set at factory C/D Drive Select Jumper ------------------------ x CLOSED Drive is MASTER OPEN Drive is SLAVE You can daisy-chaining two drives on the AT-bus interface. To configure a drive as the Master (Drive 0), a jumper could be installed at the C/D pins. Samsung ships SHD-3101A/3062A/3061A hard drives from the factory with the C/D jumper installed (Drive 0). To specify a drive as a Slave (Drive 1), remove the C/D jumper. DSP Drive Slave Present Jumper ------------------------------- In combination with the current C/D jumper setting, the DSP jumper implements one of two possible configurations: When the drive is configured as a Master - C/D jumper is installed - the DSP jumper informs the drive that the Slave is present. The DSP jumper should be installed on the Master drive only if the Slave does not use the Drive Active/Slave Present (DASP-) signal to indicate its presense. When the drive is configured as a Slave, both the C/D jumper and the DSP jumper is not to be install. ********************************************************************** I N S T A L L ********************************************************************** SAMSUNG SHD-3101/3062/3061-A HARD DISK DRIVE USER'S MANUAL 264-01403 Notes on Installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ Mounting -------- The mounting holes on the SHD-3101A/3062A/3061A hard disk drive allow the drive to be mounted in any orientation. #6-32 UNC screws should be used. ********************************************************************** F E A T U R E S ********************************************************************** SAMSUNG SHD-3101/3062/3061-A HARD DISK DRIVE USER'S MANUAL 264-01403 Introduction ------------ SHD (Samsung Harddisk Drives) 3101A/3062A/3061A hard disk drive is a high performance, 1-inch-height form factor with the highest product- ability and quality. This uses 3 inch rigid disks, and is available with AT (Advanced Technology) interface. The SHD-3101A/3062A/3061A features and embedded AT commands to optimize system performance. Be- cause the drive manages media defect and error recovery internally, these operations are fully transparent to the user. Features -------- Key feature of the SHD-3101A/3062A/3061A hard disk drive include: - Low profile, 1-inch-height form factor - High accuracy of Rotary voice coil actuator with an embedded sector servo - Average seek time of 16 milliseconds - Low power consumption - Proprietary 32K, look ahead - Automatic error correction and retries - Transparent media-defect mapping - High-performance, in-line defective sector skipping - Reassignment of defective sector skipping - Automatic magnet latch achieving Zero power consumption - 1 : 1 interleave on read/write operations - Emulation of IBM, PC-AT, task file register and all AT fixed commands - Ability to daisy-chain two drive on the interface Seek Time --------- ----------------------------------+--------+ Track-to-Track msec. typ. | 5 | Average msec. typ. | 15 | Full-Stroke msec. max. | 29 | Latency msec. avg. | 8.34 | ----------------------------------+--------+