P I O N E E R S G 1 0 8 0 A T QUANTUM Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | 2097| | Capacity form/unform 1082/ MB Heads | 16| | Seek time / track 12.0/ 4.0 ms Sector/track | 63| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer 64 KB Landing Zone Data transfer rate 12.625 MB/S int Bytes/Sector 512 16.600 MB/S ext PIO4 Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 55 | -40 65 Power: sleep W Humidity % 5 85 | 5 95 standby W Altitude km 3.048| 12.192 idle W Shock g 10 | 70 seek W Rotation RPM 4500 read/write W Acoustic dBA 30 spin-up W ECC Bit 48BIT ON THE FLY,SMART MTBF h 300000 Warranty Month 36 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** QUANTUM PIONEER SG JUMPER SETTING +---------------------------------------------------------+ | |XX | |XXI | |XXN | |XXT | |XXE | |XXR | |XXF | |XXA | |XXC | |XXE | |XX1 | |xx | |xx | | | |XX Power | |XX +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** QUANTUM PIONEER SG JUMPER SETTING Jumper Setting ============== ATA CABLE PIN+ Not Used +--------------------------------------1----------++--------+ |* * * * * * * * * * * * * * * * * * * * * * * * *| XXXXXX | |* * * * * * * * * * * * * * * * * * * * * * *| xxxxxx | +--------------------+----------------------+-+-+--+-Power--+ Blank key DS+ | PK CS Single Drive = DS only Master Drive = DS only Slave Drive = No Jumpers Quantum IDE disk drives have multiple jumper setting options and are used to set specific drive features. The most common settings are used to define the drive as the primary or secondary drive on the IDE cable. Master / Slave -------------- Quantum IDE drives have additional jumper settings used for optional features found on the drive. Listed below are the various jumper options that may be found on Quantum IDE drives and the corresponding feature that they enable. DS Jumper - Drive Select ------------------------ Used to identify the drive as the primary (MASTER) drive in a single or dual drive configuration. This is the factory default setting. SP Jumper - Slave Present ------------------------- Used only when the second (SLAVE) drive in a two drive configuration does not support DASP. DASP ---- (Drive active / drive 1 present) is a CAM (Common Access Method) defined signal that indicates the presence of a second drive, DASP is used during power on initialization and after a reset. Prior to this definition, products were introduced which did not utilize this method to detect the presence of a second drive. The SP jumper is used on the MASTER drive, with the DS jumper, when the second drive does not support DASP. CS Jumper - Cable Select ------------------------ Only used in systems that support the cable select feature. Cable Select allows for each IDE disk drive to be jumped the same and the position on the cable determines the ID. This requires a special cable and both drives on the interface would have to support this feature. PK Jumper - Park (Spare) ------------------------ This jumper does not enable any feature. It is used, instead, to provide a spare location to any jumper removed from the drive during a configuration change. ********************************************************************** G E N E R A L ********************************************************************** QUANTUM ATA TIPS Comparing the Fast ATA and Enhanced IDE Disk Drive Interfaces ------------------------------------------------------------- Why are Fast ATA and Fast ATA-2 Important? Faster data transfer rates are important because a computer is only as fast as its slowest component. Today's 486, Pentium, and PowerPC-based computers offer processor speeds many times faster than only two years ago. Bus speeds have also increased with the inclusion of 32-bit VL and PCI local buses, which have a maximum data transfer rate of 132 MB/second. Faster buses mean that data can be transferred from the storage device to the host at greater speeds. Fast ATA and Fast ATA-2 allow disk drives to store and access this data faster, thus enhancing the other high-speed components in the system and removing the bottleneck associated with older ATA/IDE drives. In short, Fast ATA helps bring very high performance to desktop PC systems. In addition, when compared to SCSI, Fast ATA is the least expensive way to achieve faster disk drive data transfer rates and higher system performance. The implementation of Fast ATA through system BIOS provides performance without incremental hardware co sts. Older systems can support Fast ATA using an inexpensive host adapter. Fast ATA and Fast ATA-2 are easy to implement in either VL or PCI local bus systems. The hardware connection can be made using a standard 40-pin ATA ribbon cable from the drive to the host adapter. Direct connection to the motherboard further eases integration when provided by the motherboard supplier. Once connected, the high data transfer capabilities of Fast ATA can be enabled through the data transfer options found in most CMOS BIOS setup tables. Newer versions of BIOS provide automatic configuration for Fast ATA drives. Fast ATA can improve efficiency by allowing more work to be completed in less time because the computer moves data faster. Graphic, multimedia, and audio/visual software users will benefit most because the speed of those applications, which work with large blocks of data, are transfer-rate dependent. The Fast ATA and Enhanced IDE interfaces both use the local bus to speed data transfer rates. Enhanced IDE also uses the same PIO modes as Fast ATA, although a data transfer rate equal to the PIO mode 4 rate has not been announced for Enhanced IDE. The major differences between Fast ATA and Enhanced IDE are that the latter includes three distinct features in addition to fast data transfer rates. The additional features of Enhanced IDE are as follows: High-capacity addressing of ATA hard drives over 528 MB - a BIOS and device driver function. Dual ATA host adapters supporting up to four hard disk drives per computer system - a function of BIOS, operating system, and host adapter, not the drive. Support for non-hard disk drive peripherals such as CD-ROMs - a function of BIOS and the operating system, not the drive Each of these features supports improved functionality at a system level, a positive development for the industry and end users. However, support for all three features requires an extremely high degree of integration and revisions to operating systems and hard- ware, in addition to BIOS changes. Specific support is required not only for the storage peripherals but also for host adapters, core logic, the system bus, BIOS, and operating systems - virtually every major block of PC architecture. There is no central industry-supported standard that controls the features of Enhanced IDE. With no standard, some products sold as "Enhanced" may provide only one of the three features of Enhanced IDE. For example, fast data transfer rate support is be coming standard on mid-range and high-end local bus systems. This single feature could satisfy the users immediate requirements without the need for the other features of Enhanced IDE. In the future, if the same system is upgraded to add the remaining features of Enhanced IDE, users may be forced to purchase an Enhanced IDE package that contains a feature already installed. This could result in unnecessary costs, integration conflicts, and in- compatibility with original factory implementations. Fast ATA, on the other hand, represents only the fast data transfer rates for ATA hard drives (support for PIO mode 3 or 4 and DMA mode 1 or 2). Fast ATA and Fast ATA-2 data transfer rates can be easily achieved when the system BIOS and hard drive suppo rt the PIO and DMA protocols. BIOS that supports Fast ATA does not necessarily support high- capacity addressing, dual host adapters or non-hard drive peripherals. But these features are being introduced independently by system manufacturers in order to compete in the PC marketplace. All of Quantum's disk drives designed for PCs now support Fast ATA, and new products with Fast ATA support will be introduced in early 1995. The drives are also fully backward compatible with older ATA/ IDE (non-Fast ATA) BIOS. The Quantum drives support both the Extended CHS (Cylinder Head Sector) and LBA (Logical Block Address) addressing methods in overcoming the 528 MB DOS capacity barrier. Quantum drives can also be used with dual host adapters. Finally, there are no incompatibilities with Quantum hard drives that would prevent computer systems from supporting non-hard drive peripherals. Quantum drives that support Fast ATA include the following families: Quantum ProDrive LPS 170/210/340/420 Quantum ProDrive LPS 270/540 Quantum Maverick 270/540 Quantum Lightning 365/540/730 Quantum Daytona 127/170/256/341/514 Fast ATA and Fast ATA-2 are important technologies that can take advantage of the performance provided by the latest high-speed microprocessors and bus architectures. The high-speed interfaces are based on industry standard specifications and are the least expensive way to achieve faster disk drive data transfer rates. Fast ATA is not a group of features that requires an extremely high level of integration, and only represents the fast data transfer rates for ATA hard drives (PIO mode 3 or 4 and DMA mode 1 or 2). =====================================================================